1. Used Rebuilt Gardner Denver Model PZ-11 pump with all standard accessories
2. New Caterpillar engine model 3516 rated 1649hp @ 1200rpm complete with radiator cooling and all standard equipment.
3. New National Torque Converter with cooler and plumbing to engine
4. Package will be belt driven with “Kevlar” belts, dual air clutch, belt guard, clutch guard and belt tensioning system
5. Discharge pulsation damper and strainer cross with applicable flanges for discharge connections,
6. 3” pressure safety valve,
7. 0-6000 PSI pressure gauge,
8. Swab lube system, pinion shaft driven
9. 6 X 8 charge pump belt driven off pinion shaft,
10. Rod cooling system, with covers
11. Controls for engine and clutch operation will be provided
12. Components will be mounted on new 2 piece 3 runner oilfield type skid with loading hitches. One skid will accommodate the engine and converter; the second skid will have the pump and related equipment. Both master skids will be pinned and designed for easy alignment.
13. Completed package will be load tested to rated pressure, cleaned and painted to your specifications.
National 8P-80 (800 HP) Triplex Mud Pump, p/b Caterpillar D-379 diesel
engine, air start, c/w full gauge panel (RPM, oil pressure, water pressure,
manifold pressure, fuel pressure), pinion driven, charging pump, Hydril
pulsation dampner, air clutch (Remote Shut-Off), air volume tank with dryer,
liner flushing pump c/w waterbox, Oteco reset relive valve, 4" x 5,000 psi
mud valve, Oteco mud gauge 0-5,000 psi.
All above mounted on 3-Runner oilfield skid (34'L x 11'6"W x 10'3"H), fully
enclosed for winterization purposes, c/w all fuel lines, air lines (roof
mounted).
Brand New EWCO chinise make 500 HP, Mud pump unitised with Brand new Caterpilar C-15 engine or 12V71 through brand new Allison HT 750 Transmission with other accessories mounted on heavy duty oil field skid
1 EACH HALLIBURTON HT400 PUMP WITH 4-1/2" PLUNGERS SERVICED COMES
> WITH NEW FILTER ELEMENTS,NEW OIL,NEWVALVE RUBBERS.
>
> COUPLED TO A GM 8V71 ENGINE SERVICED WITH NEW FILTERS,NEW ENGINE OIL
> AND DYNOTESTED BY 3RD PARTY SHOP.
>
> AND MANUAL TRANSMISSION .
>
> ALL ON A SKID WITH AIR STARTER,PANEL,RADIATOR.
HT400 PUMP WITH 4-1/2" PLUNGERS SERVICED COMES
> WITH NEW FILTER ELEMENTS,NEW OIL,NEWVALVE RUBBERS.
>
> COUPLED TO A GM 8V71 ENGINE SERVICED WITH NEW FILTERS,NEW ENGINE OIL
> AND DYNOTESTED BY 3RD PARTY SHOP.
>
> AND ALLISON 750 TRANSMISSION REFURBISHED AND DYNOTESTED BY 3RD PARTY
> SHOP
>
> ALL ON A SKID WITH AIR STARTER,PANEL,RADIATOR.
TOTAL 7 UNITS AVAILABLE(1 UNIT WITH 4" PLUNGERS,1 UNIT WITH GM 8V92 ENGINE)
size 1-5/8 x 5, gear ratio 7.118-1, max RPM 209
cap 26,9 GPM, suction press 75-80 PSI, discharge press. 4300 PSI, serice Ethylene Glycol
Complete on skid with reduction gearbox and electrical motor: Siemens, electrical mtor, model 1ma4 280 B3 280S
220V 188A/380V 108 A, max RPM 1485, IP54, 50HZ, class B, 58 KW, EEX e II, T1/T2/T3
Used Refurbished Continental Emsco Triplex Mud Pump
model 1300 HP with fluid end and discharge manifold
max. liner size x stroke: 7" x 12"
gear ration 4.31:1
Pulsation dampener 20 gallon - 5.000 Psi
Discharge strainer block
Reset relief valve 3"
Mud gauge
Drive assembly c/w one each dual clutch.
Mud pump modules are in fully refurbished condition.
Fluid ends provided with new gaskets, seats, valves, valve
springs and also c/w new piston rods and piston rod clamps.
Liners and pistons included.
Pump mounted on one heavy duty oilfied skid with:
New Caterpillar Engine model 3516 MUI land mechanical diesel engine, serial: 71Z00421, arrangement no. 4W0285
Fan hub through flywheel housing with load test report, complete with 46/CV radiator
Specification model 3516:
Mechanical engine, direct injected, turbocharged, aftercooled, engine rating: 1400 HP at 1200 RPM, 16-cylinder, 4 cycle, 170 mm bore x 191 mm stroke (6.7 in bore x 7.5 in stroke), counter clockwise rotation (as viewed from flywheel end).
New National Oilwell Varco Torque Converter
model C300-125 FH, complete
inclusive of shock mounted oil temperature and pressure
gauges: integral circulating pump: cooling connections,
heavy duty output shaft and bearings and with the following arrangement:
for direct mounted on a sae # 00 engine flywheel housing;
complete with spline drive, support plates and fresh water
heat exchanger cooling system
New Caterpillar Engine model 3516 MUI land mechanical diesel engine, serial: 71Z00421, arrangement no. 4W0285
Fan hub through flywheel housing with load test report, complete with 46/CV radiator
Specification model 3516:
Mechanical engine, direct injected, turbocharged, aftercooled, engine rating: 1400 HP at 1200 RPM, 16-cylinder, 4 cycle, 170 mm bore x 191 mm stroke (6.7 in bore x 7.5 in stroke), counter clockwise rotation (as viewed from flywheel end).
New National Oilwell Varco Torque Converter
model C300-125 FH, complete
inclusive of shock mounted oil temperature and pressure
gauges: integral circulating pump: cooling connections,
heavy duty output shaft and bearings and with the following arrangement:
for direct mounted on a sae # 00 engine flywheel housing;
complete with spline drive, support plates and fresh water
heat exchanger cooling system
upon request
2 EACH HALLIBURTON HT400 PUMPING UNITS WITH 4-1/2" PLUNGERS(PUMP IS LIKE NEW CONDITION ,THE ENGINES OLD HOUR METER SHOWED READINGS OF 27HRS) COUPLED TO GM 8V71 ENGINE(SERVICED) AND ALLISON 750 TRANSMISSION(DYNOTESTED).
NEW PANELS AND GAUGES.
AIR STARTER.
ALL ON A SKID RADIATOR COOLED.SKID IS DETACHABLE INTO 3 PIECES AND MADE OF ALUMINIUM.
